Airmar SS200—No Fairing Manuel d'utilisateur télécharger pdf

Follow the precautions below for optimal

product performance and to reduce the risk of

property damage, personal injury, and/or death.

WARNING: Always wear safety goggles and a dust

mask when installing.

WARNING: Immediately check for leaks when the

boat is placed in the water. Do not leave the boat

unchecked for more than three hours. Even a small

leak may allow considerable water to accumulate.

CAUTION: Always operate the transducer in water.

Operating in air will allow the transducer to overheat

possibly resulting in failure.

CAUTION: The stainless steel housing must be

isolated from a metal hull to prevent electrolytic

corrosion. Use the isolation sleeve and washers

supplied.

CAUTION: SS422—The transducer must be oriented

properly. The mark on the face must be forward and

parallel to the centerline of the boat.

CAUTION: Never pull, carry, or hold the transducer by

the cable as this may sever internal connections.

CAUTION: Never strike the transducer.

CAUTION: Never use solvents. Cleaner, fuel, sealant,

paint, and other products may contain solvents that can

damage plastic parts, especially the transducer’s face.

IMPORTANT: Read the instructions completely

before proceeding with the installation. These

instructions supersede any other instructions in your

instrument manual if they differ.

17-008-06 rev. 03 11/22/13

Thru-Hull with Stem & No Fairing

Depth Transducer

Models: SS200, SS422, SS502

Tools & Materials

Safety goggles

Dust mask

Permanent marker

Electric drill

Drill bits and hole saws:

Pilot hole 3mm or 1/8"

SS200, SS502 23mm or 15/16"

SS422 25mm or 1"

Sandpaper

Mild household detergent or weak solvent (such as alcohol)

File (installation in a metal hull)

Marine sealant (suitable for below waterline)

Knife or scissors (installation in a metal hull)

Slip-joint pliers

Grommet(s) (some installations)

Cable ties

Water-based anti-fouling paint (mandatory in salt water)

Installation in a cored fiberglass hull (see page 4):

Hole saws for hull interior: 35mm or 1-3/8"

Cylinder, wax, tape, and casting epoxy

Mounting Location

Guidelines

CAUTION: Do not mount in line with or near water intake or

discharge openings or behind strakes, struts, fittings, or hull

irregularities that will disturb the water flow.

CAUTION: Do not mount the sensor where the boat may be

supported during trailering, launching, hauling, or storage to avoid

damaging the transducer’s face.

• The water flowing under the hull must be smooth with a

minimum of bubbles and turbulence (especially at high speeds).

• The transducer must be continuously immersed in water.

• The transducer beam must be unobstructed by the keel or

propeller shaft(s).

• Choose a location away from interference caused by power and

radiation sources such as: the propeller(s) and shaft(s),

machinery, other echosounders, and other cables. The lower

the noise level, the higher the echosounder gain setting that

can be used.

• Choose a location with a minimal deadrise angle.

• Choose an accessible spot inside the vessel with adequate

space for the height of the stem and tightening the nut.

Record the information found on the cable tag for future reference.

Part No.________________Date___________Frequency_________kHz

INSTALLATION INSTRUCTIONSOWNER’ S GUIDE &

SS200

Applications

Stainless steel transducer compatible with all hull materials.

Recommended for aluminum hulls to prevent electrolytic corrosion

provided the stainless steel transducer is isolated from the metal hull.

SS502

1 2 3 4

Résumé du contenu

Page 1 - Depth Transducer

Follow the precautions below for optimal product performance and to reduce the risk of property damage, personal injury, and/or death.WARNING: Always

Page 2 - Installation

Boat Types (see Figure 1)• Displacement hull powerboat—Locate amidships near the centerline. The starboard side of the hull where the propeller blades

Page 3 - Checking for Leaks

Page 4 - Anti-fouling Paint

Modèles reliés SS422—No Fairing | SS502—No Fairing |

Commentaires sur ces manuels

Pas de commentaire

Airmar SS200—No Fairing Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Airmar SS200—No Fairing. Airmar SS200—No Fairing User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés SS422—No Fairing | SS502—No Fairing |

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Airmar SS200—No Fairing