Airmar Splash-proof Junction Box Manuel d'utilisateur télécharger pdf

17-037-01 rev. 04 12/14/10

WARNING: Always wear safety goggles and a dust

mask to avoid personal injury.

CAUTION: High Voltage Charge

The depth transducer may be storing a high voltage

charge. Accidental discharge could destroy the speed

sensor.

IMPORTANT: Please read these instructions

completely before proceeding with the installation.

These instructions are to be used in conjunction with

your instrument manual and the instructions provided

with your transducer(s), sensor, or other components.

Junction Box

Terminal Style

Applications

• To provide a water, fog, and salt-resistant splice.

• To splice marine cables up to 7.5mm (5/16") in diameter.

• To splice marine cables with up to eight wires.

(Two crimp connectors are included for additional wires.)

• To splice Airmar TRIDUCER

multisensor and other Airmar

cables.

Pre-Installation Test

NOTE: For Airmar Products Only

1. Connect the transducer or multisensor to the echosounder with

the transducer in the water and aimed at the bottom. Check for

a depth reading on the instrument (and temperature reading if

applicable).

2. To check the speed and temperature functions, connect the

sensor to the instrument. Spin the paddlewheel and check for a

reading of several knots. Check for the approximate air temp.

3. If a test produces no reading, check all the connections and

repeat the test. If a function (depth, speed, or temperature) is

inoperative, do not install the unit; return it to the dealer.

Tools & Materials

Safety goggles

Dust mask

Screwdrivers: Phillips and blade

Pencil

Drill

Drill bit: 3mm or 1/8"

Box-cutter knife (some installations)

Cutting pliers

Alcohol

Wire strippers

Crimping pliers (nine or ten-wire cables)

Petroleum jelly (nine or ten-wire cables)

Cable ties

Parts Needed

CAUTION: Do not puncture unused grommets.

1. Remove the red cap and the contents of the junction box

including the terminal block (see Figure 1).

2. The type of sensor and the size of the cable determine which

instructions to follow (see Table 1 on page 4). Determine the

grommets that will be needed. Using a small Phillips

screwdriver, puncture the center of the appropriate grommets.

NOTE: The small grommets (marked 3-5) provide moisture

sealing for cables from 3.5–5mm (1/8–3/16"). The large

grommets (marked 5-7) provide moisture sealing for cables

from 5–7.5mm (3/16–5/16"). Both set of grommets can

accommodate smaller cables than suggested, but the sealing

will be less effective. Larger cables can be used, but insertion

will be difficult.

3. Set aside the sleeving that will be needed.

Mounting Location

1. Select a convenient dry mounting location along the cable route,

preferably 1–1.5 m (3–5') from the transducer/sensor to

facilitate future replacement.

2. Position the junction box so the grommets are easily accessible

to the cable. Mark the location of the mounting holes.

3. At the marked location, drill two 3mm or 1/8" holes

approximately 10mm (3/8") deep. Do not fasten the junction

box in place at this time.

connector

black sleeving

large diameter

sleeving

small diameter

sleeving

terminal block

tab (2)

grommet (4)

Figure 1. Junction box and contents

terminal

terminal screw

mounting screws

mounting

block

screws

(16)

screw (2)

cap

INSTALLATION INSTRUCTIONS

1 2 3 4

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

17-037-01 rev. 04 12/14/10WARNING: Always wear safety goggles and a dustmask to avoid personal injury.CAUTION: High Voltage ChargeThe depth transducer

Page 2 - Multisensor

2A. One-cable TRIDUCER® MultisensorNOTE: These instructions are not for use for with zip-cable (follow instruction B).PreparingCAUTION: Take care not

Page 3 - Closing & Mounting

34. Apply alcohol to each cable jacket to ease sliding. Carefully push approximately 203mm (8") of each cable segment through the appropriate gro

Page 4

4 Table 1: Instructions and Materials NeededSensor Type Instruction Grommets SleevingTRIDUCER® multisensorC332 or C347 cableA2 large(marked 5-7)C332:

Commentaires sur ces manuels

Pas de commentaire

Airmar Splash-proof Junction Box Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Airmar Splash-proof Junction Box. Airmar Splash-proof Junction Box User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Airmar Splash-proof Junction Box