Airmar P52 with Plastic Release Bracket 20-039 Manuel d'utilisateur télécharger pdf

17-003 rev. 06 04/12/11

Transom Mount with Release Bracket 20-039

Transducer or TRIDUCER® Multisensor

Model: P52

Tools & Materials

Safety goggles

Dust mask

Screwdrivers

Wrenches

Scissors

Masking tape

Electric drill

Drill bits and hole saw or spade bit:

Bracket holes 4mm, #23, or 9/64"

Fiberglass hull chamfer (preferred), 6mm, or 1/4"

Transom hole (optional) 19mm or 3/4"

20mm or 13/16" (Furuno)

Cable clamp holes 3mm or 1/8"

Marine sealant (suitable for below waterline)

Straight edge

Pencil

Zip-ties

Water-based antifouling paint (mandatory in salt water)

Identifying Your Model

The model name is printed on the cable tag.

Applications

• Not recommended for boat with large inboard engine(s).

• Good operation up to 40kn (46MPH).

• Vertically orients the sound beam on hull with deadrise angle up to 22

• Adjusts to transom angles of up to 20°

Assembly

1. Attach the left release arm to the bracket back by first inserting a hex nut

into the recess in the back of the bracket. Place the arm firmly against

the bracket back and insert a #10-32x5/8" screw with a flat washer

through the holes. Tighten it in place (see Figure 1). Repeat this

procedure with the right release arm.

2. Slide the flat washer and spring onto the #10-32x2" screw and insert it

into the hole in the left release arm. Insert a nylon-insert lock nut in the

right release arm hole with the nylon side facing outward. Tighten the

screw until the spring is flush with the surface of the release arm. Do

not over-tighten.

3. P52—Attach the sensor to the bracket by placing the bracket inside

(see Figure 2). Use four #10-32x5/8" screws and flat washers. Fasten

them in place with nylon-insert lock nuts, nylon side facing outward.

Tighten the screws, so the sensor remains in place but can be adjusted.

P37

Figure 1. Bracket assembly

#10-32x2"

#10-32x5/8"

flat washer (3)

nylon insert lock nut

hex nut (2)

spring

right

left

bracket back

screw

screw (2)

release

arm

Figure 2. Attaching sensor to bracket

inside

bracket

flat washer

INSTALLATION INSTRUCTIONSOWNER’S GUIDE &

Follow the precautions below for optimal product

performance and to reduce the risk of property

damage, personal injury, and/or death.

WARNING: Always wear safety goggles and a dust

mask when installing

WARNING: When the boat is placed in the water,

immediately check for leaks around the screws and

any other holes drilled in the hull.

CAUTION: This is an impact release bracket only.

Attempting to manually release the bracket may cause

damage.

CAUTION:

The bracket protects the sensor from frontal

impact only.

CAUTION: Never pull, carry, or hold the sensor by the

cable as this may sever internal connections.

CAUTION: Never strike the sensor.

CAUTION: Never use solvents. Cleaners, fuel, paint,

sealants, and other products may contain strong

solvents, such as acetone, which attack many plastics

greatly reducing their strength.

IMPORTANT: Please read the instructions completely

before proceeding with the installation. These

instructions supersede any other instructions in your

instrument manual if they differ.

NOTE: Attach the brackets

to the inside of the sensor’s

mounting tabs

shown

1 2 3 4

Résumé du contenu

Page 1 - 17-003 rev. 06 04/12/11

17-003 rev. 06 04/12/11Transom Mount with Release Bracket 20-039Transducer or TRIDUCER® MultisensorModel: P52Tools & MaterialsSafety gogglesDust m

Page 2

2Mounting LocationCAUTION: Do not mount in an area of turbulence or bubbles: near water intake or discharge openings; behind strakes, struts, fittings

Page 3 - Operation

3Mounting & Adjusting1. Cut-out the template (see Figure 5).2. At the location selected , position the template so the arrow is aligned with the b

Page 4 - Cleaning

4Setting the Bracket Release PointCAUTION: Never compress the top of the spring below the tab, because the bracket will be locked in place and will no

Commentaires sur ces manuels

Pas de commentaire

Airmar P52 with Plastic Release Bracket 20-039 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Airmar P52 with Plastic Release Bracket 20-039. Airmar P52 with Plastic Release Bracket 20-039 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Airmar P52 with Plastic Release Bracket 20-039