Airmar 1 kW—TM258 Manuel d'utilisateur télécharger pdf

17-299-02 rev. 04 01/09/14

Transom Mount, 1kW with Short Release Bracket

Depth Transducer

with Temperature Sensor

Models: TM258, TM260, TM265LH, TM265LM,

TM270W, TM275LH-W

U.S. Patent No. 7,369,45; 8,582,393. UK Patent No. 2 414 077

Tools & Materials

Safety goggles

Dust mask

Angle finder

Masking tape (some installations)

Pencil

Electric drill

Drill bits and hole saws:

Bracket holes 5mm, #4, or 7/32"

Transom hole (optional) 18mm, 11/16", or 3/4"

21mm or 13/16"

(Furuno, Raymarine only)

Cable clamp holes 3mm or 1/8"

Marine sealant (suitable for below waterline)

Socket wrench

Straight edge

Small screwdriver

Grommet(s) (some installations)

Cable ties

Water-based anti-fouling paint (mandatory in salt water)

Applications

• Recommended for outboard and inboard/outboard sport fishing

powerboats 8m (25') and up

• Not recommended for inboard powerboats

• Not recommended for stepped hulls

• Adjusts to transom angles from 3°–21°

• Bracket protects transducer from frontal impact only

Mounting Location

Guidelines

CAUTION: Do not mount the transducer in line with or near water

intake or discharge openings or behind strakes, fittings, or hull

irregularities that may disturb the water flow.

CAUTION: Avoid mounting the transducer where the boat may be

supported during trailering, launching, hauling, or storage.

• For best performance, the transducer’s face must be in contact

with smooth water. To identify an area of “clean” water, observe

the flow off the transom while the boat is underway.

• Allow space above the bracket for it to release and rotate the

transducer upward.

• Mounting on the side of the transom where the propeller blades

are moving downward is preferred (see Figure 1).

• Mount the transducer as close to the centerline (keel) of the

boat as possible to ensure the transducer’s face remains in the

water when the boat is turning. However, be sure it is a

minimum of 15 cm (6") beyond the swing radius of the propeller,

so the water passing under the transducer does not cause a

flow disturbance to the propeller.

Record the information found on the cable tag for future reference.

Part No.________________ Date___________ Frequency________ kHz

Follow the precautions below for optimal

product performance and to reduce the risk of

property damage, personal injury, and/or death.

WARNING: Always wear safety goggles and a dust

mask when installing.

WARNING: When the boat is placed in the water,

immediately check for leaks around the screws and

any other holes drilled in the hull.

CAUTION: CHIRP transducer—Always operate the

transducer in water. Operating in air will allow the

transducer to overheat resulting in failure.

CAUTION: Never pull, carry, or hold the transducer by

the cable as this may sever internal connections.

CAUTION: Never strike the transducer to release it.

When mounted on the bracket, remove the transducer

by removing the locking pin and hinge pin.

CAUTION: Never use solvents. Cleaner, fuel, sealant,

paint and other products may contain solvents that can

damage plastic parts, especially the transducer’s face.

IMPORTANT: Please read the instructions completely

before proceeding with the installation. These

instructions supersede any other instructions in your

instrument manual if they differ.

Figure 1. Mounting location on single drive boat

15cm (6")

minimum beyond

swing radius

NOTE: Starboard

side of hull where

propeller blades

are moving down-

ward is preferred.

hull projection

0–3mm (0–1/8")

parallel to

waterline

TM260

bracket with shims

operational position

INSTALLATION INSTRUCTIONSOWNER’ S GUIDE &

1 2 3 4

Résumé du contenu

Page 1 - Depth Transducer

17-299-02 rev. 04 01/09/14Transom Mount, 1kW with Short Release BracketDepth Transducerwith Temperature SensorModels: TM258, TM260, TM265LH, TM265LM,

Page 2 - Installation

Figure 2. Stepped transom space requirementTM258: 244mm (9-3/4")Boat Types• Single drive—Mount a minimum of 15cm (6") beyond the swing radi

Page 3 - Stabilizing the Bracket

Mounting & Adjusting the BracketCAUTION: Do not position the leading edge of the transducer lower than the trailing edge because aeration will occ

Page 4 - Maintenance

Modèles reliés 1 kW—TM260 | 1 kW—TM265LH/LM | 1 kW—TM270W | 1 kW—TM275LH-W |

Plus de documents pour Capteurs Airmar 1 kW—TM258

Voir le document Airmar 1 kW—TM258 Manuel d'utilisateur

Airmar 1 kW—TM258 Manuel d'utilisateur (4 pages)

Commentaires sur ces manuels

Pas de commentaire

Airmar 1 kW—TM258 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Airmar 1 kW—TM258. Airmar 1 kW—TM258 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 1 kW—TM260 | 1 kW—TM265LH/LM | 1 kW—TM270W | 1 kW—TM275LH-W |

Plus de documents pour Capteurs Airmar 1 kW—TM258

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Airmar 1 kW—TM258